HPE6-A85 Exam: Absolutely Free Online Practice

Question 1
- A network technician is using Aruba Central to troubleshoot network issues Which dashboard can be used to view and acknowledge issues when beginning the troubleshooting process?
  A : the Alerts and Events dashboard
  
  B : the Audit Trail dashboard
  
  C : the Reports dashboard
  
  D : the Tools dashboard
  
  Answer: A
Question 2
- What are the main characteristics of the 6 GHz band?
  A : Less RF signal is absorb by objects in a 6 GHz WLAN.
  
  B : In North America, the 6 GHz band offers more 80 MHz channels than there are 40 MHz channels in the 5 GHz band.
  
  C : The 6 GHz band is fully backward compatible with the existing bands.
  
  D : Low Power Devices are allowed for indoor and outdoor usage.
  
  Answer: B
Question 3
- After having configured the edge switch uplink as requested your colleague says that they have failed to ping the core You ask your colleague to verify the connection is plugged in and the switch is powered on They confirm that both are correct You attempt to ping the core switch and confirm that the ping is failing. Knowing the nature of this deployment, what commands might you use to troubleshoot this issued
  A : Ping 10.11 1 - ping the core to attempt to verify connectivity Show trunk - to verify if the LAG interface was correctly added to the switch Show spanning tree - to check for spanning-tree blocked states Show port-access clients interface all - to view any port-access blocking states or failed authentication attempts on all interfaces Show run interface vlan20 - to double check the layer 3 svi configuration is correct for l_3 connectivity Show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports
  
  B : diagnostic diag cable-diag 1/1/51 diag cable-diag 1/1/52 - to view diagnostic information for the physical link to get a status on any interruptions to Layer 1 connectivity, show ip route - to verify that the default gateway is present in the routing table show ip ospf - to check whether there is a layer 3 routing protocol enabled show ip dns - to view whether there is a valid dns source
  
  C : Ping 10.1.1.1 - ping the core to attempt to verify connectivity show lacp agg - to verify which link aggregations are currently configured using which physical ports show lacp int - to verify the LACP status and whether any links are blocking in your topology show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports show run interface 1/1/51.1/1/52-to ensure the physical interfaces are no-shut and members of the lag show run interface lag 1 - to ensure the correct vlan trunking configuration is applied to the logical interface show run int vlan 20 - to ensure you have the L3 SVI no shut and configured in the correct subnet
  
  D : Show run - to view the running configuration of the switch Show run | begin 20 "vlan 20" - to ensure VLAN 20 was correctly added to the database show run | begin 20 'interface vlan 20' - to view the L3 SVI configuration Show run interface 1/1/51.1/1/52 - to ensure the physical interfaces are no shut and were added as members of LAG 1 Show run int lag 1 - to verify LACP mode active was configured to eliminate LACP blocking states
  
  Answer: C
Question 4
- You are configuring a network with a stacked pair of 6300M switches used for distribution and layer 3 services. You create a new VLAN for users that will be used on multiple access stacks of CX6200 switches connected downstream of the distribution stack You will be creating multiple VLANs/subnets similar to this will be utilized in multiple access stacks What is the correct way to configure the routable interface for the subnet to be associated with this VLAN?
  A : Create a physically routed interface in the subnet on the 6300M stack for each downstream switch.
  
  B : Create an SVl in the subnet on each downstream switch
  
  C : Create an SVl in the subnet on the 6300M stack, and assign the management address of each downstream switch stack to a different IP address in the same subnet
  
  D : Create an SVl in the subnet on the 6300M stack.
  
  Answer: D
Question 5
- What happens when the signal from an AP weakens by being absorbed as it moves through an object?
  A : APs will use bonded channels to decrease latency to clients
  
  B : Signal to Noise Ratio (SNR) increases
  
  C : Signal to Noise Ratio (SNR) decreases
  
  D : Aruba Central dynamically moves clients to neighboring APs
  
  Answer: C

Free HP HPE6-A85 Exam Questions

Absolute Free HPE6-A85 Exam Practice for Comprehensive Preparation